Car owners, often go to 4S shop to maintain the car, car wash is no exception, if only a simple car wash brush, you can bring their own car wash high pressure pump, you can personally wash the car, and now Xiaobian To talk about the car wash pump installation steps and precautions. Car washing high pressure pump First, the car washing high pressure pump installation steps Use a good place for the machine, be careful not to the machine on the sun or wet and rainy place, and the chassis properly grounded to ensure safety, and then use a suitable length and size The harder hose sleeve in the pump suction port connector (note the stuck tight seal can not leak), and through the tube into the pump cylinder filled with water, until filling up, and then random with a net cover attached to the suction pipe The other end, and then install the outlet pipe according to the purpose. If used for car washing or engage in hygiene, the car wash water pipe can be connected to the pump head outlet and connected to the water gun, pinch the water gun switch (open), close the power to spray a powerful high-pressure water for users to use, To change the shape of water spray, simply release the water gun switch (short time off the water) and then spin the gun on the copper head to the appropriate location. Such as for pumping or other purposes, the water pipes set directly on the outlet pipe and tied, with the same method used in ordinary pumps. If you want to change the size of the pump pressure or flow, you can move the small handle on the pump head to adjust, and pay attention to the reading of the table, how much to adjust in a certain range, is very convenient. Second, car washing high-pressure pump Notes 1, the first time do not forget to pump cylinder irrigation, the pump water stored in the pump after a short period of time generally do not leak, the next time you use the closing brake can work. If the machine should not be upside down within the pump for a long time to prevent corrosion of water within the machine parts, at the same time remove the rubber sleeve placed separately to avoid the screw and rubber sleeve adhesion, to be reloaded with. 2, the machine is equipped with automatic back pressure device, stop working when the red stop motor overload, but in order to save power consumption, reduce mechanical wear and prolong the service life of the machine, the power should be shut down to stop washing, not long-term closure of the water gun and Not related to the motor phenomenon. 3, the long-term unused and out of the machine within the sleeve, the motor will appear again when the phenomenon of immobility after irrigation and try to power, such as the normal rotation of the machine can be assured that if you can not turn off the power immediately disconnect To prevent damage to the motor. The main reason that the motor does not turn is that the screw in the machine is stuck with the rubber sleeve. At this time, the pump cover and the motor hood are removed, the rubber sleeve can be removed with the action of both ends, and the rubber inside the rubber sleeve is cleaned and coated Some lubricants (butter rape oil can be) re-installed on the machine that can be rotated normally. 4, the use of the machine screw wear and tear will reduce the flow and pressure impact on the cleaning effect, just open the pump head for the same effect can be with the same screw. There is no other more structure of the machine, apart from the pump cylinder at a glance, in addition to replacing the screw almost no other maintenance, routine maintenance can be completely resolved by the user, as long as the proper use of attention, the machine will not normally fail, the user need not worry, rest assured use. Further Reading: pump valve pipe fittings Exhibition Water Expo Xiamen exhibition of marine equipment Internet + Forum Yiwu Fair 2016 exhibition mold top ten brands of the Internet information industry (Xiamen) Technology Co., Ltd. Author: Asian pumps Network Editor: Yao Xiaoxia (QQ / WeChat:) http://beng.liuti.cn/ (Service Hotline:)
Rockwool Felt
Description:Rockwool FELT is a kind of insulation materials with chosen high-quality natural rock as the main raw materials,such as basalt,dolomite,melted in the cupola,centrifugate into fiber in high speed by four rollers centrifuger and sparying a certain amount of binder,dust proof oil and moisture repel.
ROCKWOOL FELT have higher strength and better elasticity. The folded rock wool board with certain compression resistance has greater drawing strength, and it does not tend to peel off and has greatly improved durability.
The Advantage of Fireproof Rock Wool Insulation and Mineral Wool Insulation
1) Small coefficient of heat conductivity and good capability of heating preservation;
2) Excellent fireproof capability, Excellent sound absorption and sound insulation capability;
3) Green building materils and no harm for body;
4) The rock wool has higher and better elasticity;
5)The folded rock wool board with certain compression resistance has greater drawing strength, and it does not tend to peel off and has greatly improved durability.
6)The felt can be with wire or glassfiber for reinforced.
7)The size can be 1m or 1.2m width,length can be made according to client's request.
Rockwool Felt
Rockwool Felt,Rock Wool Felt,Rock Wool Felt With Wire,Rock Wool Felt With Glass
HEBEI HENGDA SEALING MATERIALS CO.,LTD. , https://www.hengdasealing.com