Waterproofing is an important part of the renovation. Waterproofing is used in the interior, with particular attention to the kitchen and toilets. These are the main sites for water use. If the kitchen and toilet are not waterproof enough, it will not only affect the indoor environment, but also may cause leakage of the houses of neighbors downstairs, resulting in the loss of neighborhood relations! So, what should you pay attention to when doing waterproofing ? We now take a look at what to do water should pay attention to it!
First, the details of the waterproof project
1, the basic treatment
Want to do a good job of waterproofing, grassroots handling is very important! Before we do waterproofing, we must first carefully clean the ground, you can use a fine brush to remove the surface of the floating ash, cement blocks, check the substrate, to ensure that it is solid and clean. Second, we must carefully clean the water pipes, drains, yin and yang corners and various corner gaps, and then special treatment! When brushing waterproof paint, pay attention to brushing it from top to bottom, brushing from the wall to the ground!
2, brushing to be comprehensive
We do waterproof, not just waterproof kitchen, but also according to the family's water situation, according to local conditions, if the balcony, basement area and other areas have also taken the water pipe, or shop on the ground to warm, these places need to be waterproof! In addition, in some details, such as the need to bury water pipes in the walls, it is necessary to chisel in the walls and apply waterproof coating to make it waterproof; also, if you want to change the position of drainage pipes and floor drains, you need to Location is waterproof!
3, bathroom waterproof 1.8 meters high
Bathroom wall waterproof must be higher than 1.8 meters, because the shower or spray are generally installed at a height of one meter eight, waterproof is only higher than one meter eight, in order to achieve results! And the rest of the bathroom non-shower wall waterproof should not be less than 35 cm, but if you want to achieve better waterproof effect, it is best to do all the walls of the bathroom are eight meters waterproof! In addition, it should be noted that if the bathroom wall is a light wall or self-built wall, then the waterproof coating must be brushed to a thickness of 1.5 mm, which is the national standard waterproof layer thickness! The height of the waterproof layer can also reach the top!
Second, waterproof detection
1. Closed water test in the bathroom for 24 hours
After 12 hours of brushing the waterproof coating, you can do a water shut-off test. Pay attention to the closed water test must wait until the waterproof coating and the grassroots firm combination can be done, otherwise there is no effect! Before closing the water test, first say hello to the neighbors downstairs. Then seal the water outlet and the doorway; when the water shutoff test is done, it is required that the water storage height be 3-5 cm, and make a mark. Wait for 24 hours; after the water shut-off test, observe whether the water level has dropped and if the ceiling below the house is seepage. Failure on the contrary, the whole redo!
2, light wall water experiment
For wall waterproofing inspection, a watering test may be adopted, that is, after the water wall is poured from the top to the bottom of the light wall for 3 minutes, pay attention to the requirements. 4 When you are young, look for water seepage on the other side of the wall. If not, then pass!
Tips:
The kitchen and balcony are also the key points for waterproofing. Generally, the kitchen floor and the wall must be waterproof for 30 cm. If the balcony is not closed, if there is wind and rain, there will be water residue. Therefore, the balcony floor also needs waterproofing.
On the relevant content of what should be noted for waterproofing , Xiao Bian introduced it here for everyone, and hopes to help everyone! Waterproofing is just a link in the decoration, but it is very important and directly affects the quality of life in the future. Therefore, waterproofing needs to be careful! For more information, please follow this site!
Decoration waterproof bathroom waterproof bathroom waterproof how to do bathroom waterproof bathroom how to do waterproof
1.Application : For medical care
2.Dimension: Customized dimension, OEM & ODM
3.Material: A6063, A6061, A3003 and other series alu alloy
4.Suface treatment: Anodizing, polishing, turning ,power coating, mill finish etc
5.Equipment: CNC ,extruding machine, cold drawn machine, heating oven, straightening machine, cutting machine
|
OD |
OD Tolerance |
ID Tolerance |
Roundness |
Straightness |
Circular run-out |
|
φ16-20 |
±0.02 |
±0.02 |
0.01↓ |
0.015↓ |
0.05↓ |
|
φ20-30 |
±0.02 |
±0.02 |
0.01↓ |
0.015↓ |
0.05↓ |
|
φ30-50 |
±0.05 |
±0.05 |
0.02↓ |
0.020↓ |
0.08↓ |
|
φ50-80 |
±0.15 |
±0.10 |
0.05↓ |
0.025↓ |
0.10↓ |
6. STANDARD PACKING:Wooden case/carton
7. Trade Terms
1. Payment: 30% T/T in advance, 70% balance pay before delivery. L/C at sight.
2. Delivery time: 20 days after deposit receiverd. If opening mould, plus 7-10 days.
3. Trade Term can be chosen depending on your requirements.
4. FOB Port: Shanghai
Drawn Tube For Medical Care,Medical Aluminum Drawn Tube,Aluminum Drawn Tube For Medical,Medical Aluminum Drawn Pipe
Changzhou YiFei Machinery Co., Ltd. , https://www.yifeialu.com