Paving tiles pay attention to do a good job of four-step quality and quantity

Buy tiles to pay attention to many aspects of the assessment, tiling is more stressful, of course, tile stickers is good or good look at the decoration master craftsmanship, good craftsmanship, posted tiles gloss is good, flat, free Tiles are inspected before drums are tiled, and they are pre-arranged to prepare them for subsequent paving.

Brand Store: Wells Tiles Mona Lisa Tiles

1, before paving first check the formal decoration company will conduct related checks before laying tiles. First check the dimensions of the outer box tiles, specifications, color number and other labels are the same; then open the box to check the tiles. Tiles can only be tiled if they meet relevant regulations.

Although each product will have more or less certain error, paving the tiles is not a problem as long as the error is within the allowable range.

2. Pre-arrangement of ceramic tiles pre-arranged for pre-arrangement before paving. The standard for pre-arrangement is every corner of the tile and every end of the wall. The size of the tile can't be lower than 1/3 of the width of the finished tile. This is due to the aesthetic demand for tile laying. If the width of the tile is less than 1/3, it is necessary to arrange two tiles together and use two tiles to balance the size of the remaining tile.

3, the wall must be flat before paving tiles, pay attention to check the flatness of the wall, which is directly related to the flatness of the tile after laying the problem.

Some workers in this area will be more negligent. If the error of the wall surface roughness is large, although the thickness of the tile and wall cement mortar can be remedied, correspondingly, the thickness error of the cement mortar between the tile and the wall to be laid out will be larger. The strength of cement slowly rises, water evaporates, and the degree of evaporation of the tile's moisture differs from the degree of shrinkage of the cement, which can easily cause unevenness in the brick surface.

The best practice is to make a test on the wall in the previous period. If the wall roughness is within 1cm, you can rest assured; if the wall roughness is more than 1cm, you need to deal with it in advance. It is recommended to fill the wall with cement mortar first to ensure that the thickness of the cement mortar adhered to the wall tile is consistent with each other. Tiles are tiled at intervals of 24 hours. This minimizes the problem of uneven brick surface. Of course, the uneven brick surface may also be caused by the technical reasons of laying workers.

4, tile immersed water to do enough before paving tiles, but also pay attention to the ceramic tile to be flooded enough to allow the tiles to fully eat enough water, this is to avoid hollowing and shedding of tiles.

The traditional tile laying method uses cement mortar for paving. First of all, the proportion of cement mortar should be reasonable, the general practice is that the volume ratio between the two is 1:1. If this is the case, the ceramic tile is still empty, in addition to the technical level of the workers in the paving process is not high, the main reason is that the pre-drawing tile is not enough.

The so-called tile draught is to put the tiles in the water in advance soaked for a period of time, usually in about 2 hours, the actual operation can be based on specific analysis of the concrete density of the tiles. This is done to ensure that after the tiles are affixed to the wall, the moisture in the cement mortar will not be snatched away by the tile to achieve its maximum strength, so as to prevent emptying and falling off of the tiles, which is the most important reason for tile soaking. If the tile is not soaked in water, it will take away the moisture in the cement mortar, reduce its strength, cause the ceramic tile and the wall surface to reduce the adhesion, a long time prone to tile emptying and shedding. In addition, pay attention to the gaps in the tiles and the density of the cement mortar to reach a certain standard. It is normal that the emptying rate of bricks accounts for less than 5% of the entire wall surface.

As a consumer, tile-laying this kind of work can not be done. Of course, all we have to do is to carefully inspect the tiles when we buy the tiles. It is better not to have too much color difference so as to avoid causing trouble to the subsequent paving.

Links: How to Calculate Area and Quantity in Floor Tiles

Tile tile tile window decoration cement decoration decoration company

Aluminum planks allow the user to cover more work area without moving equipment.

It`s made of aluminum, lighter weight and more durable than the traditional products made of wood or bamboo.

Best suited for construction and building maintenance applications, always be used as an attachment for aluminum ladder and scaffolding.

Extension planks

Aluminum Planks