Latest fire rescue equipment parameters and usage procedures

As a professional mine and pit rescue tool, it is mainly used for mines and deep wells trapped in caves, hills and high-rise buildings, etc., to rescue people. The set consists of a tripod, a capstan and a foot chain.

 

Product parameters:

Features

1, using high-strength lightweight alloys to ensure strength while minimizing weight

2, three legs can be retractable, easy to carry and transport

3. Universal design of head rings to ensure easy installation of winch hooks

4, large area foot design, ensure the area of ​​land, there is a bow-shaped hook hook at the foot, equipped with a chain of protection, to ensure the stability and safety of the tripod

5, winch positive and negative self-locking structure to ensure the safety of the sling

6, the use of special stainless steel sling rope, breaking high pull, good flexibility

7, easy to install, adjustable height, can be placed at the wellhead, pit mouth, etc. to quickly rescue trapped persons

Use procedure

1. Shake the manual winch to control the wire rope up and down to achieve the purpose of rescue.

2 , with a falling self-locking device, that is, when suddenly rose to shake in the air, when the load, or people will not fall down, only shaking the handle in the opposite direction, the wire rope will move downward.

Precautions

1. The rescue tripod is a lifting device. Before each use, check whether the safety cable can be normally wound on the winch.

2. The rescue tripod should be stored in a dry place and must not be stored together with corrosive liquids such as acids and alkalis.

 

Inspection and maintenance

Check once a month to check if the connection is strong and there is no rust.

Product Overview: One-piece garments made from hoods, chemical protective clothing, chemical-resistant gloves, chemical-resistant rubber boots, and zippers are chemical protective clothing worn by emergency personnel to handle chemical events such as acid and alkali. , anti-aging, cold, anti-gasoline and other properties. The product is divided into a fully enclosed form. The fully enclosed garment is hermetically sealed to prevent harmful gases from entering the garment.

Closed form

Fully closed

model

GRS

Materials

Flame-retardant fabrics, PVC

Material thickness

0.65mm

Penetration data

A stupid, sulfuric acid, chlorine, dichlorinated alkane equal to or greater than 480 minutes

Fire equipment configuration

Built-in

Respirator backpack

Have

Overpressure exhaust valve

Have

ventilation system

Have

Hood

Big vision one-piece hood

Chemical rubber boots

Chemical protection gloves

Have

Use procedure

Wear air respirator as required.

Pull off the chemical protective clothing zipper, put two feet into the pants, put the pants to the waist, put on the boots.

Put both arms into the two sleeves, pull the zipper and wear it.

Two people with the appropriate operation.

Precautions

Before use, the clothing must be carefully inspected for damage. If it is damaged, use is strictly prohibited.

It cannot be used in an environment with excessive temperature.

It cannot be used in fires, nor can it be used in potentially explosive atmospheres.

Inspection and maintenance

Monthly inspections and pre-use inspections are strictly prohibited during the storage period. They must not be exposed to sunlight, and must not be exposed to reactive chemical substances and various oils.

Product Overview: The multi-purpose thrower is composed of a drop launcher, a miniature gas cylinder and an inflatable lifebuoy. The inflatable lifebuoy is composed of a housing, a TPU air chamber, an automatic inflation device and a CO2 gas cylinder. Prior to use, a lifebuoy is loaded into the launch tube of the casting launcher. The lifebuoy is connected together by a gas chamber and the like and is wrapped in a casing. A water inlet hole is left in a section of the casing and a throwing rope is connected in the other section. This product is also equipped with a 120- meter throwing rope, which can be quickly connected with the life buoy. After preparing the above work, the insurance knob on the tossing device is rotated to be insured, and then the CO2 gas bottle is thrown into the transmitter. Fill the compressed gas to make the drop emitter ready for launch.

weight

Dumping device ≤3.5kg, buoy <0.6kg

Inflatable molding time

≤5s

Lifebuoy buoyancy

≥78.4N , buoyancy loss ≤5% after 24 hours

Cast rope length

120 meters

Use ambient temperature

-30 °C -+65 °C

Projectile distance

80 - 100 meters

Use procedure

1. Pull the return spanner backwards hard. After hearing the sound of “ 啪 ” , the firing rod is ready to be reset; turn the cutout knob to the “OFF” position.

2. Pull out the fork when throwing.

3. Immediately rotate the handle upwards to pierce the gas cylinder and release the gas to the air chamber. The pressure gauge indicates 3.5MPa to 4Mpa .

4. When throwing and firing, turn the cutout knob to the “ON” position so that it aligns with the protrusion mark on the handle and is in the open state.

5 , cast the target to be rescued and to trigger the trigger to cast.

Precautions

1 , can not be placed in sunlight exposure for a long time, avoid contact with oil, acids and other chemicals.

2. The lifebuoy should be stored in a room with a temperature of 0-350C and a relative humidity of less than 85% , and it should not be squeezed.

 

Inspection and maintenance

1. The life cycle is valid for three years and the quality of the cylinders is tested every year. 2. After the lifebuoy is used, air-tightness inspection must be performed by professional technicians, and replace the new cylinder with automatic inflation device and shell.

 

The German Dräger HPS 6200 new fire helmet has the best wearing comfort and excellent technical safety. The helmet is the lightest helmet in accordance with EN 443:2008 . The helmet is paired with the new full face mask Dräger FPS 7000 and the advanced compressed air respirator Dräger PSS 7000 with a unique protection system.

Product parameters

● Certified by EN443 .

●The helmet shell is made of high temperature resistant thermosetting plastic

● With chin strap

● a visor equipped with: an amber-colored polysulfone, a double-sided high temperature, scratch-resistant coating, in line with EN 14458 standard

● retractable chin band, and with vlecro (Velcro) velcro fastener ergonomic and high temperature.

● can be equipped Panorama-Nova-Supra, f2- Supra- adapter, and a belt system adapted to the new Q-fix and S-fix the Dräger FPS 7000 full face protection.

● Helmet weight is currently the lightest kind

Use procedure

In the rescue of the fire, tighten the cap buckle and start the fireproof shawl. Place the mask in a timely manner when the fire source is near or the eyes and face are damaged.

Precautions

Never touch the helmet with fire and clean it after use to prevent collision and contamination. The torch remains intact and easy to use.

Inspection and maintenance

Helmets, masks, and shawls should be kept clean and undamaged. The flashlight should be charged in time after use.

Product Overview: Fire fighting suits are used for full-body prote

Curtain Style

Curtain Style,High Quality Curtain Style,Curtain Style Details, Huanghua Techo Building Material Co., Ltd.

Huanghua Techo Building Material Co., Ltd. , http://www.insectsscreen.com