The difference between sliding doors and sliding doors is to let everyone know about sliding doors and sliding doors.
In fact, the concept of sliding doors and sliding doors in the market is very vague. It seems that as long as the sliding doors are called sliding doors or sliding doors, and some sliding door or sliding door manufacturers do not classify the two, they are collectively referred to as the two. A variety. In fact, the sliding door is evolved from the sliding door. It can be said that it is a fine classification of sliding doors. The two are different in some aspects. The following nine positive building materials network introduces the difference between the sliding door and the sliding door:
First, the use of sliding doors are used as cabinet doors, cloakroom doors, closet doors, partition doors, bathroom doors, etc.; sliding doors are widely used, mostly used as balcony doors, kitchen doors, bathroom doors, and can also be used for entry doors.
Second, the door cover and the set of lines.
The sliding door only has the function of partitioning. Generally, there is no door cover and set of wires; the sliding door not only requires the function of partitioning, but also requires sealing, heat preservation and sound insulation. Therefore, there are generally door sets and sets of wires, and the frame of the door cover has a hook. , the seal is stronger.
Third, the lock.
The sliding door is generally unlocked.
Sliding door multi-install locks.
Fourth, the hardware pulley.
The sliding door is generally complete with upper and lower pulleys, and the sliding door generally has only the lower pulley.
Fifth, the thickness of the profile.
Sliding doors and sliding doors now use aluminum alloy, aluminum-magnesium-titanium alloy and other alloy materials as the most frame materials. Generally, the profiles used for sliding doors are relatively thin, mostly 0.8MM~1.0MM thick profiles, while the sliding door profiles are the thinnest. It is 1.0mm thick, even thicker than 1.8mm thick, the sliding door is heavier, stronger and more load-bearing. [ Follow the WeChat public account "Jiuzhengmen Window Network"; pay attention to courtesy, scan code to send millions of business opportunities! Jiuzhengmen window network exchange group ]
ABS plastic,full name acrylonitrile–butadiene–styrene copolymer,
Acrylnitrile butadiene Styrene copolymer has a good thermal and dimensional stability and high impact strength(also at low temperature).It is strong,shows a good scratch resistance and has a good dimensional stability .ABS Plastic can be used in temperatures ranging from -50'C to +70'C .it mainly have ABS SHEET,ESD ABS SHEET,FIREPROOF OF ABS SHEET,ABS+PC SHEET.
Classification:
ABS plastic according to impact strength can be divided into: ultra high impact type, high impact type, medium - resistant type and so on;
ABS plastic can be divided into: injection, extrusion, pressure delay, vacuum and blow molding.
ABS plastic can be divided into: general grade, heat resistance grade, plating grade, flame retardant grade, transparent grade, anti-static, extruding plate and pipe grade, etc.
Advantages:
1.Good mechanical strength, high impact strength
2.Resists scratching, Excellent abrasion resistance
3.Good electrical properties, moisture and creep resistance
3.High dimensional stability, good luster
4.Good chemical and stress cracking resistance to inorganic salt solutions, alkalis and many acids(strong oxidizing acids is a exception).
Disadvantages:
1.Endurance in water ,endurance in corrosion of inorganic salt. But not endurance in organic solvent.
2.ABS Plastic is easily to cracked by the effects of the organic solvent.
3.Poor weather resistance, easily to change color and become brittle because of the sunlight.
Application:
1. Electronics & electric appliances: antenna socket, coil former, wiring board, convertor, speaker,connector, and other parts;
2. Food industry parts;
3. Building model, model mockup;
4. Electronic industrial parts, freezer and refrigeration industry;
Notes:
1. ABS Plastic is strict requirements for flame retardant grade ABS to prevent the decomposition of flame retardants.
In the start of the power, the cartridge should be cleaned with general grade ABS plastic and then processed.
(point to stop for more than 20 minutes before the downtime), on the one hand must cut cylinder temperature below 100 ℃, on the other hand must be emptying the material inside the cylinder, and general level ABS cleaning cylinder rear can stop.
The purpose is to make flame retardant ABS not decomposed.
2. The use of reworked material for primary or secondary sex thousand net, without impurities, no decomposition of ABS plastic reworked material, can be used directly after crushing, also can mix with the new material, the mixing ratio is generally not more than 25% of the new material, so as not to affect performance.
For more than 5 times more than 5 times or adding the fresh material with colorant, generally not mixed with the new material, mainly to prevent the color difference.
ABS Plastic must be dried and processed in accordance with the regulations, whether it be separately regenerated or mixed with new materials.
Combustion characteristics
Specification: the diameter of the ABS Plastic rod can be produced from 2mm to 250mm. The conventional length is 1000mm, and the length is unlimited.
The thickness of ABS Plastic sheet material can be produced from 0.3mm to 1.9mm, the normal width is 600mm, the width cannot exceed 1200mm, the length is not limited.
The thickness of plate can be produced from 2mm to 180mm, the usual specification of 2-10mm is 1000mm* 2000mm, and the commonly used specification of 10-180mm is 600*1200mm. ABS Plastic can also be customized according to requirements, and the width cannot exceed 1200mm, and the length is not limited
Color: beige or white, can also be made black and color, and the color order is 500KG.
Modified varieties:ABS Plastic can be added to the fiberglass, copper powder and molybdenum disulphide to enhance the bar.
Add antistatic agent to the permanent antistatic electric bar, and the volume resistance value is between 6 to 9 power of 10.
Add flame retardant to flame retardant rod from UL 94V-0 to HB flame retardant grade. Other modification requirements are customized according to customer's actual use.
Product certification: ABS Plastic most environmental certification reports and safety reports for raw materials, such as SGS report, CTI report, UL report, MSDS safety information, etc.
ABS Plastic Sheet,Antistatic Styrene Plastic Sheet,Esd ABS Plastic Sheet,Fireproof ABS Plastic Sheet
Dongguan Noegem Plastic Products Co.,Ltd , http://www.noegempLastic.com