Correction method for closing the shaft hole

Home>Bearing knowledge>Revision method for closing shaft hole
/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131";

Correction method for closing the shaft hole

Source: China Bearing Network Time: 2013-07-16

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';
(1) Detect the wear depth of the shaft hole; if the wear depth is less than 4 mm in the diameter direction (ie, the radius direction is less than 2 mm); use the power tool to polish the part to be repaired. Pay attention to: the outer surface should not be polished too much; the rougher the better.
(2) Use the Keisin 1755 scavenger to remove the outer surface of the bearing hole.
(3) Apply a thin layer of Kesaixin 1731 release agent on the outer ring of the bearing; in order to facilitate the disassembly of the bearing in the future.
(4) Manufacturing 2311 antifriction repair agent.
(5) Apply the repairing agent directly to the outer ring of the bearing; but only apply to the rear half of the outer ring of the bearing. The amount of coating should ensure that there is no glue between the outer ring of the bearing and the shaft hole; The gap is completely filled.
(6) Push the bearing coated with the repair agent into the shaft hole.
(7) Wipe off the extruded repair agent. Again, when pushing the bearing, make sure that the repairing position is not lacking in glue.
(8) Position the bearing.
a. The simplest method is to install the shaft together with the bearing; after the accuracy is determined, the repair agent is cured in this direction.
b. Conditions can be used; can be positioned or installed by three-point gasket positioning method or manufacturing fixture.
(9) It can be put into use after it is completely cured.
Recommend to friends comments close window

Bearing related knowledge
Industrial INA self-aligning ball bearings "protection strategy" large inventory of damage caused by counterfeit bearings
PY160C motor grader transmission input bearing damage treatment bearing internal structure low noise bearing selection tips


This article links to http://
Please indicate the bearing network http://

Previous:Seven Mistakes in the Application of Smooth Grease in Bearing Repair: The Common Bearing Wear and Causes

Veneer Mdf board is mainly used for laminate floor, door sheet, partition, furniture,  decoration of indoor&outdoor, office and home furniture, sould equipment, inside decoration of the car, antistatic floor of computer room, panel, security door, wall board etc, and also used for the package and the basic material of laminate Wood Flooring.

Veneer MDF Board is easily for coating finishing, every coating, oil paint are also on the surface of Veneer  MDF , is the fist choice as the basic material of painting effects.Veneer MDF is one kind of beautiful material of decoration. Smooth and flat surface, fine texture, steady property. All kinds of venner, gummed paper, light metal plate, melamine paper etc, is also can on the surface of the Plain MDF . Plain MDF is made from acoustical board after drilling, is used in construction decorative progress, such as meeting room, displaying room, office etc. And we have  Veneer UV MDF and Sapele Veneered MDF.

LULI Group Corp. Ltd, well known as the leading manufacturer for wooden, steel and paper products, located in Shouguang, Weifang, Shandong, China. Since the foundation in 1985, it focus on the production of Plywood , venner,MDF board, Particle board, Door Skin , Blockboard , Finger joint board, OSB , paper, Steel etc.

Veneer Mdf Details:

size:1220*2440MM 1830*3660MM 1830*2440MM 915&610*3660MM 1220*2800MM 1525*2440MM

THICKNESS:2MM-35MM

MATERIAL:POPLAR, COMBINE, PINE

GLUE:E0, E1, E2, FIRE-PROOF

CERTIFICATION:CARB, FSC, CE, SON CAP

veneer mdf

Veneer Mdf

Veneer Mdf,Veneer MDF Pegboard,Veneer UV MDF,Sapele Veneered MDF

Luli Group Co.,Ltd. , http://www.cnluli.com

Posted on